Wednesday, May 25, 2011

Single Phase Phantom Load Tester Manufacturers Exporters India

‘RE’ Phantom Loading Bench suitable for 3 phase 4 wire, 3 phase 3 wire and single phase Meters with Electronics and Electro-mechanical type.

Single phase Phantom Load Test set having following details:


Input voltage: 230 Volts.


Output voltage: 300 V


Output current: 0.5, 1.0, 2.5, 5.0, 25.0, 40.0, 80.0 Amp


Power Factor: .0.5, 0.8 Lag – lead through unity.


Metering: Voltmeter, Ampere meter & PF meter – Digital


Capacity: Testing of three meters at a time.


Control: Voltage & Current control will be through variacs.


For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Magnetizing Coil Manufacturers Exporters to Oman, Yemen

A.C. Magnetic Coil design for working on 400V, 50 HZ AC supply capable to induce 28000 Amp turns for testing the magnetic influence on Energy Meter, Circular AIR Core coil having 200 mm OD,38 mm ID,50 mm depth (.27tesla)





For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Induced Over Voltage Test Set (I.O.V.W.) / D.V.D.F. Exporters to Saudi Arabia, United Arab Emirates (UAE)

INTRODUCTION

Induced Over Voltage Test Set is used for testing the strength of insulation between turns and between other points of the transformers etc. as stipulated by BIS or other standard specification. For this test Double Voltage is applied across L.T. terminals for one minute, and to control the magnetizing current over voltage frequency is applied.

It is and independent unit having coupled motor and Generator with Control Panel to control the motor ad output voltage. Depending upon the design requirements AC or DC motors are used.

SPECIAL FEATURES
  • No foundation required
  • Unit ready for use.
  • Fine Voltage control.
  • Short Circuit Protection.
  • Calibrated Voltage and Ampere Meter.
  • Easy to operate complete with operator safety features.
  • Guaranteed for one year against manufacturing defects.
  • Efficient After Sales Service.




TECHNICAL DETAILS

The control panel consists of direct on-line or Star-Delta depending upon capacity of the setup. Moving Coil Voltmeter and Ammeter are provided to indicate the output voltage and current. Frequency meter is provided to check output frequency. While for measuring input voltage and current, moving iron type meters are used. Other included parts consists of variac, indicators, control switches and operator safety features. In case of DC motor, DC drive is used to control/vary the frequency.

INPUT VOLTAGE : 415V, 3 phase 50Hz AC supply

OUTPUT VOLTAGE : 0 -1500 V or As Required

OUTPUT FREQUENCY : 100 Hz to 400 kHz or As Required

CAPACITY : Upto 2000 kVA or As Required

FOUNDATION : Not Required

PROTECTION : Zero Start Inter Locking, Overload Protection, Single Phasing Preventer etc


For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Heat Cycle Test Manufacturers Suppliers Bahrain, Qatar, Lebanon

Heat Cycle Test Set is designed for working on 400 V, 2 phases of 3 phase AC supply. The unit shall generate 3000 Amperes in cables loop of 11 meter of suitable capacity.

The set shall comprise of the following:-
i) Control Panel
ii) 2 Nos. Current Injection transformer (suitable for output of 3000 Amps at 7.5 V each.)




TECHNICAL DETAILS

i) Control panel shall consists of the following:
• Motorised voltage regulator oil cooled type designed for 2 phase of 3 phase AC supply.
• Moving Iron type 96 Sq. mm Voltmeter to indicate incoming voltage of the regulator.
• Moving Iron type 96 Sq. mm Voltmeter to indicate output voltage of the regulator.
• Moving Iron type 96 Sq. mm Ammeter of suitable range to indicate primary current of loading transformer.
• Moving Iron type 96 Sq. mm Ammeter and current transformer to indicate secondary current of loading transformer.
• Digital temperature controller to control the automatic switching ‘ON & OFF’ of cable heating.


For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Variable Auto Transformers - AC Electrical Machines Suppliers Iran, Iraq, Kuwait

Wherever voltage control is required, ‘RE’ Variacs makes it very simple by providing Toroidally wound Auto Transformer for variable voltage. If you have not yet used ‘RE’ Variacs you are missing some important benefits of using electric power.

The maximum current that can be drawn depends on the size of the wire used. The ‘RE’ Voltage regulators are manufactured from 2 A to 2000 A for Single and Three Phase.

Special Features

  • Compact in Size.
  • Easy to operate.
  • Special Insulating Paper is used for transformer winding.
  • Guaranteed for one year against manufacturing defects.
  • Efficient After Sales Service.



Technical Specifications

‘RE’ Variac Continuously Variable Auto Transformers usually form part of system in which other components such as transformers. Diode etc. are used as power components, ‘RE’ Variac Engineers are well experienced in such applications and are always available for consultation to prospective users.

The proportion between iron section and copper turns is such that at the maximum AC applied voltage maximum NO LOAD current is within 5%.

The insulation of the wire over one face is removed the output is taken between one end and the brush arm. The moving Brush contacts the next turn before it breaks away from the previous turn, thus, there is no interruption in output voltage.

‘RE’ Variac is designed to Boost the Output, Voltage by 12% than the input voltage.

Three Single phase units are connected in star for 3 phase four wire system. The brush arms are moved by a common shaft and the Star point is connected to the neutral of the system. A three phase voltage variable from zero to 470V is obtained, if the Input voltage is 415V in case of single phase 270V is obtained if input is 240V. Custom made capacities can be manufactured and as yet the manufacturing range covers upto 2000 Amperes in three phase.

OPTIONAL: ‘RE’ Variacs are available with motor drive. The type of motor used for driving is specially made for this application. It is 240V AC motor operating with speed of 60 RPM synchronous at 50Hz. It is instantly reversible and can be stopped without overrun. It speed depends on frequency i.e. 60 RPM at 50 Hz. Supply. The desired speed is obtained by suitable by gearing. It starts stops & reverses instantly. It is ideal for automatic voltage control through Electronic system. *It can be stalled indefinitely without over heating.



For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Tuesday, May 24, 2011

500 VA Phase Shifter Suppliers Turkey, Syria, Israel, Jordan

500 VA Phase Shifter suitable for working on 400/415 Volts 3 phase 50 Hz. AC supply shall be provided to be connected in potential circuit having phase angle control 90-0-90 Lag and Lead.

The Phase Shifter shall be independent unit and shall have approximate weight of 40 Kg.
i) All desired indication shall be provided.
ii) A Phase sequence indication shall be provided for RYB – RBY.
iii) A Voltmeter shall be provided.

The unit shall be naturally air cooled type and designed for field use duty.


For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Resistive Load Bank Manufacturers Exporters to Costa Rica, Panama



For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Inductive Load Bank Suppliers Cuba, Puerto Rico




For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Inductive & Resistive Load Bank - AC Electrical Machines Venezuela

Inductive & Resistive Load Bank



For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Pre Heater Manufacturers Exporters to Colombia, Bolivia, Ecuador

Pre Heater



For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Servo Voltage Controlled Stabilizer Exporters to Paraguay, Uruguay, Chile

Servo controlled Voltage Stabilizers (SCIVS) are specifically designed to manage input fluctuations of various trends. The output voltage can be controlled to within +/- 1.0%-+/-0.5% of the desired output. For this precise control a solid state circuit with a permanent magnet motor, is utilized and proficient gear system.

'RE' manufacturer Servo controlled Industrial Voltage Stabilizer upto2000kVA in three phase and up to 300kVA in single phase.

The Servo controlled Industrial Voltage Stabilizer over the rating of 1000kVA can be designed for use in 11,000 KV or 415 V i.e. HT or LT

SPECIAL FEATURES

  • Available in HL/LT.
  • New innovated design for HT.
  • High Capacity available.
  • Economic to buy & use.



TECHNICAL DETAILS

Transformer: Double wound buck & boost type continuously rated, impregnated in insulating varnish is used for output voltage control. The transformer is made of (CRGO) silicon Steel Lamination & Electrolytic copper wire is used for winding Voltage

Control: A motorized sleeplessly controlled auto transformer is used for controlling the output voltage.

Electronic Circuit: Control Circuit with I.C. is provided to continuously monitor the output voltage.

Input Voltage Ranges:
Single Phase : 130-285 any range in between
Three Phase : 225-440, 300-44-, 340-440 or as per requirement

Output voltage : 220-240 V + 1% or 0.5 % (Single Phase)380-415 V + 1% or 0.5 % (Three Phase)

Control :

  • Potentiometer for output voltage setting.
  • Switch for manual and auto use.
  • Push button to increase or decrease voltage manually in case of manual position.


Metering : A Voltmeter is provided to indicate the output voltage.

Protection :
The design of the unit is such that it can withstand 20 percent overloading for short durations without any damage. Each unit consists of minimum-maximum range indicator, motor movement control micro switch at the end of the range and oil imlet & outlet valve, oil level indicators, lifting arrangement, for whole unit and transformer only, cooling radiator as per the capacity requirement.

Optional :
Amper meters, on-off switch's fuse, change over switch, under-over voltage protection & indication, with or without tripping, arrangement, single phase protection, with or without contactor.


For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com

Friday, May 20, 2011

Inductive Load Manufacturers Suppliers Brazil, Peru, Argentina

RE’ 6kVA Inductive Load designed to testing single phase Meter Power Supply etc. The unit shall be designed for working on 230/250V single phase 50Hz AC Supply having output voltage 0-600 V at 10 Amps. The load is rated continuously for temperature rise test. The unit shall be complete with knob to control the current and power factor independently.




For further details

Call us at: +91-11-41425851 / 52
E-mail us at: info@re-india.com